Welcome to Unk's Guns! Licensed F.F.L. Manufacturer CUSTOM AR15 & AR10
NEW AND COOL STUFF AT UNK'S

NEW AND COOL STUFF AT UNK'S
Jason Kipfmiller, Madison Kipfmiller, and me Rick Kipfmiller
Buddy the Beagle
YOU MUST CALL PRIOR TO COMING TO OUR LOCATION. WE SEE CUSTOMERS IN PERSON BY APPOINTMENT ONLY.
THAT WAY WE CAN MAKE SURE WE ARE THERE!!!
THE ADDRESS IS:
94 OAKWOOD DRIVE
DAHLONEGA, GA 30533
WE ARE ONE OF THE ONLY ADDRESSES LEFT IN THE WORLD THAT THE GPS IS SOMETIMES WRONG!! CALL WHEN YOU GET CLOSE!
CHECK OUT THE NEW VIDEO BELOW!
VERY LIMITED PRODUCTION!! IF NOT IN STOCK WE WILL DO OUR BEST TO FILL ORDERS.
Even the video is less than 7 minutes long! It really shows the simplicity of installation of my FIRE ON PULL AND FIRE ON RELEASE TRIGGER.
Check out this great video. Pay attention to the trigger finger action!
TAKE ACCURACY TO A NEW LEVEL!! New Prototype!!
Please reach us at rkipfm@gmail.com if you cannot find an answer to your question.
The 2 Position Fire on Pull and Release trigger is engineered closely to the original Armalite/Colt design of the AR15 and AR10 weapons. This was done to keep dependability intact. And as such we did not add extra parts to the trigger assembly. So, our FOPAR 2 Position Trigger DOES NOT HAVE A THIRD FUNCTION. It is controlled by the 2 position safety switch and your choices are: Fire on pull and release-or-Safe.
There is a work around if you do not wish to let the second (fire on release) shot go down range:
1) KEEP FIRM REARWARD PRESSURE ON THE TRIGGER
2) USING YOUR OFF HAND PULL THE CHARGING HANDLE TO THE REAR
3) WITH THE CHARGING HANDLE PULLED FULLY TO THE REAR THEN & ONLY THEN-
RELEASE THE TRIGGER
4) RELEASE THE CHARGING HANDLE
5) MOVE THE SAFETY SWITCH TO THE SAFE POSITION
Also please note: YOU CAN BUY A FOPAR TRIGGER AND A AR15 LOWER CHEAPER THAN A COMPETITORS TRIGGER ALONE! So you can have a dedicated lower or you can purchase a complete lower with the 2 Position FOPAR around $300.00... WOO-HOO!
Not at this time, But we will look at it in the future.
Yes you can! A Mil Spec lower with parts kit, 2 Position FOPAR trigger and buffer, buffer tube, buffer spring installed MUST BE SHIPPED TO AN F.F.L. dealer for delivery. Website special price is $299 and $1 Shipping to the lower 48.
Yup! They are made by man not by God so...
This happens on about 3 percent of the mil spec hammers. the Hammer sometimes is mil spec except for the disconnect hook on the rear of the hammer. they are sometime a few thousand of an inch out of spec. This can be fixed by 1. A couple swipes with a file across the disconnect hook on the hammer. 2. Replace the hammer with one known to be within spec. We suggest using Anderson Manufacturing stainless steel hammers they are in spec and are a speed hammer to boot... So BONUS! I will post a video on it soon.
Light primer strikes have nothing to do with the FOPAR trigger but if you removed the hammer and spring when installing about 50 percent of the time the hammer spring is reinstalled backwards. Just make sure the hammer spring is in correctly.
CHECK ALL LOCAL, STATE, AND FEDERAL
LAWS PRIOR TO INSTALLING THESE PARTS!
NEWS FLASH!! THEY ARE HERE!
High end mil spec or BETTER. As good if not better than Spikes or Aero or Daniel D. and in DAHLONEGA GA!
Stripped lower- $99.00 Complete lower- $329.00
At this time we only have them to fit the AR platform.
You can order by calling 770-634-0635 M-F 10AM to 3PM If I don't answer leave a message!
Currently all orders must be paid by credit/debit card by phone. OR CASH IN PERSON.
New guns are priced at Level 2 Wholesale. I would rather sell a lot of guns at a little profit than none at a lot of profit!
Can Launchers that can throw a 12oz can up to 100 yards... Even FIRE ON PULL AND FIRE ON RELEASE TRIGGER equipped Lowers!
OUR OWNERS MANUAL
THE INSTALLATION SHEET
Rick Kipfmiller, Owner
Unk’s Guns and No B.S. Accessories Co.
Re: Determination of Patent Infringement
This Notice is to inform you that pursuant to a stipulated judgment entered by the
U.S. District Court for the District of Nevada, Unk’s Guns and No B.S.
Accessories Co. will no longer manufacture, sell, or offer for sale its three position
FOPAR trigger products as these products incorporate technology that
was invented by Franklin Armory and is protected by U.S. Patent No. 10,393,461
(“’461 Patent”). Any of my previous instructions concerning how to make pull release
triggers should be disregarded, and in fact, if followed could result in the
creation of an illegal or dangerous firearm.
For those of you who have previously purchased one of Unk’s Guns and No B.S.
Accessories Co.’s three-position FOPAR “pull-release” trigger products, I want to
clarify that any representations concerning the compliance of such products with
state and federal firearms regulations only reflect my opinion. Unk’s Guns and No
B.S. Accessories Co.’s products have not been reviewed by an independent
consultant or the BATFE for the purpose of determining compliance with federal
firearms laws and regulations. Because I am not an attorney, I also cannot advise
you concerning whether Unk’s Guns and No B.S. Accessories Co.’s products
comply with your local state and federal firearms regulations.
Sincerely,
Rick Kipfmiller.
Copyright © 2018 Unk's Guns - All Rights Reserved.
Powered by GoDaddy